Setra-system Model 595 Instrukcja Użytkownika Pobierz pdf

Model 595 Slimline

Submersible Pressure Transducer

Setra Systems, Inc.

Adding a Site Offset to SDI12 Output

In some applications it is necessary to measure a site value including some

reference data point, for example sea level. Assuming the sensor is installed 10m

above sea level, then it is possible to have all reported readings add 10m, thus

acquiring the data without the need for further modification. To add a site offset

then:

1. Determine the offset to be applied.

2. Add the offset to the pressure units (e.g. aXU1,10!)

3. Save new calibration to nonvolatile memory (e.g. aXS0!)

4. Verify sensor now measures 10m for 0 applied pressure.

10. WARRANTY

The company warrants its products to be free from defects in material and

workmanship in normal use and service for a period of two years from date of

shipment. The Company reserves the right and option to repair or replaceupon

evaluation of the returned original part. Modification, misuse, attempted repair by

others, improper installation or operation shall render this guarantee null and

void. The Company makes no warranty of merchantability or fitness for a part or

purpose.

11. Servicing

The transducer cannot be repaired locally and if damaged should be returned to

ourselves at the address shown below when a replacement/repair is required.

Setra Systems, Inc.

159 Swanson Road

Boxborough, MA 01719

Attn: Repair Department

12. Return to Factory

PLEASE NOTE: All returns must be accompanied with Setra’s “Calibration and

Service Order” return form. The form can be downloaded at:

http://www.setra.com/tra/repairs/pdf/webrepair.pdf

Any instrument returned without Setra’s authorized form completely filled out

will be quarantined and no action will occur. It may ultimately be returned to you

and subject to a transportation charge.

159 Swanson Road, Boxborough, MA 01719/

Toll Free: 800-257-3872/ Phone: 978-263-1400/

Fax: 978-264-0292/Email: [email protected]/Web: www.setra.com

ISO

✓

Certified

9001:

2000

1 2 3 4 5 6 7 8

Podsumowanie treści

Strona 1 - Setra Systems, Inc

Model 595 SlimlineSubmersible Pressure TransducerSetra Systems, Inc.Adding a Site Offset to SDI12 OutputIn some applications it is necessary to measur

Strona 2 - Contents

Contents1.0 Introduction... 32

Strona 3 - Figure 2

1.0 IntroductionModel 595 is a level measuring transducer for precise measurements of groundand surface water levels. The transducer measures pressure

Strona 4 - 6.0 Installation

● Exposed end of cable must be kept free from moisture● Liquid must not be allowed to freeze in the pressure port.5.0 Action on Receipt● Check accesso

Strona 5 - 6.2 Electrical Installation

6.2 Electrical InstallationThe 595 requires a D.C. power supply between 8V and 30V. The 595 includessuppression devices providing surge protection. In

Strona 6 - 7.1 Analogue Output Probes

It is recommended to firmly secure the Kevlar core of the cable, for example, byknotting and securing under a fixing screw.7.0 OperationHaving install

Strona 7 - 8.2 Calibration Adjustment

The temperature is a measured value and thus the density of water at any giventime is calculated by the transducer. The user may enter a local gravity

Strona 8 - 8.1 Self diagnostics

7.2.4 Setting Up a Custom Unit ScalingUnit conversion performed by the 595 is of the form y=mx+c. Where units otherthan the commonly used set provided

Komentarze do niniejszej Instrukcji

Brak uwag

Setra-system Model 595 Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Czujniki Setra-system Model 595. Setra System Model 595 User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Czujniki Setra-system Model 595